[Linrad] Re: Linrad - MAP65 communication

[ix.netcom.com; rein0zn@xxxxxxxxxxxxxxxx>]

Hi All,

Should I use 3.05 and not 3.06 with MAP65?

I just learned that 3.05 comes with the ip address
related parameter file included?

Could this be the missing link?

73 Rein W6SZ



-----Original Message-----
>From: Rein w6sz <rein0zn@xxxxxxxxxxxxx>
>Sent: Jul 16, 2009 12:51 AM
>To: Linrad <linrad@xxxxxxxxxxxxxxxx>
>Subject: [Linrad] Linrad - MAP65 communication
>
>
>Hello All,
>
>Finally gotten to the point that I would like
>to run MAP65 with a SDR I-Q or a Softrock.
>Not been very successful so far.
>
>Need some serious help please.
>
>Let me start with the computers.
>
>1 XP machine and a laptop with XP.
>
>Both computers have network cards and
>run on a WiFi router for the internet.remote
>in the house
>
>Network do cards communicate.
>
>Linrad versions run with DELTA44 or SDR I-Q
>
>Assuming that MAP65 will work with Linrad without
>compiling. Perhaps that is not so?
>
>Also that the communication part would be very
>basic ( see the the lights run on the network cards )
>
>Or perhaps some indication "data transferring"
> or so. This is possibly present ,but it does not
>show here, except the red "no rx data"
>The could be a difference between data streaming
>and "rx data present".
>
>  Matters of format
>
>I have been told that downloading the programs
>from the web sites, installing them, do it.
>Such as just linrad and WSJT.
>
>On this reflector, I see notes and message about
>IP's , par_netsend_ip, par_netsend_ip files,
>par_netrec_ip.
>
>Not even 100 % sure that I have these names correct!
>
>I must be missing an important part here or overlooking
>an important section of the installation?
>
>Have Linrad3.06 on one computer and MAP65 on the
>laptop.
>
>Have done the "N" and "8" selections. And Delta44
>selected, That part is all working as, is MAP65
>on the other computer, Can go into transmit etc
>MAP65 shows the green Receiving label as soon as
>I start MAP65, and the
>
>Red "No Rx data"....
>
>With Linrad T activated and NETSEND on, linrad
>running and receiving in SSB mode.
>
>It's quite clear that the 2 computers are not working
>together.There is also no activity visible on the network
>card led's. In Dos I can PING the computers both ways.
>
>It looks that linrad in the send mode is not able to
>communicate with the other computer most likely
>due to lack of the correct IP
>
>From the reflector I have deciphered that the IP's need
>to be processed or put in a file.
>
>It is frustrating to me that with some 250 network
>messages one way or another on this reflector.
>( Google MAP65 network ) and that that I can't
>figure this all out myself,
>But that is what it is
>
>In the linrad directory is a file par_network,
>created when I did "N" or perhaps "R".
>That is all I see network related.
>
>I have also gotten the impression that
>linrad needs certain adjustments etc.
>or setting, also that it should work as
>it is downloaded.
>
>
>In the hope to get some help,
>
>73 Rein W6SZ
>
>
>
>
>
>On the master computer, I put the IP address of the destination
>computer (slave) in the par_netsend_ip => this is correct
>On the slave computer, I put the IP address of the master computer in
>the par_netrec_ip => this was not correct !!! the par_netrec_ip must
>include the IP of the slave computer itself.
>>


--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups "Linrad" group.
To post to this group, send email to linrad@xxxxxxxxxxxxxxxx
To unsubscribe from this group, send email to linrad+unsubscribe@xxxxxxxxxxxxxxxx
For more options, visit this group at http://groups.google.com/group/linrad?hl=en
-~----------~----~----~----~------~----~------~--~---


LINRADDARNIL