[linrad] Re: segmentation fault

[Dan Sawyer <earthlink.net; dansawyer@xxxxxxxxxxxxxxxx>]

Roger,

Thank you again. See below.

- Dan

Roger Rehr wrote:
> Hi, Dan,
>
> I have a couple of more questions the answers to which might help to 
> figure things out if you are still having problems with segmentation 
> faults.  As Leif noted, you should not worry about doing the hardware 
> test.  Go right to "U" to set up soundcards, then to "D" SSB OR "A" 
> Weak Signal CW.
>
> 1.  Were you using OSS from the first, before you started with Linrad?
Yes, it supports system sound.
> 2.  If so, did FC6 come with it installed or did you add it?
Yes. I have updated the kernel and it is also configured for OSS.

> 3.  Is the audio now working in Linrad when you go into "D" or "A" for 
> example from the main screen?
No. The D option asks for channels, the a baud rate. It reports input 
and output cannot work concurrently and then errors with a seg fault.
> 4.  If not, what exactly happens when you to to "U" from the main screen?
see 3.
> 5.  What version of nasm are you using?
nasm-0.98.39-3.2.2
> 6.  What kernel version are you using?
2.6.21.1
> 7.  Is your  machine 64 bit or 32 bit and if 64 bit are you running 64 
> bit version of FC6?
32 bit
> If things are working you can ignore all of these questions ;)
>
> 73,
>
> W3SZ
> Roger Rehr
> http://www.nitehawk.com/w3sz
>
>
> Quoting Dan Sawyer <dansawyer@xxxxxxxxxxxxx>:
>
> > All,
> >
> > xlinrad is now building and running. However attempts to perform the z
> > command, hardware interface test, produces a segmentation fault.
> >
> > Other sound apps, mplayer, etc run fine. The system is using OSS.
> >
> > Thanks - Dan
> >
> > #############################################################
> > This message is sent to you because you are subscribed to
> >   the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
> > To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
> > To switch to the DIGEST mode, E-mail to 
> > <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
> > To switch to the INDEX mode, E-mail to 
> > <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
> > Send administrative queries to  <linrad-request@xxxxxxxxxxxxxxxxxxxxx>
>
>
> Roger Rehr
> W3SZ
> http://www.nitehawk.com/w3sz
>
>
> #############################################################
> This message is sent to you because you are subscribed to
>  the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
> To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
> To switch to the DIGEST mode, E-mail to 
> <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
> To switch to the INDEX mode, E-mail to 
> <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
> Send administrative queries to  <linrad-request@xxxxxxxxxxxxxxxxxxxxx>

#############################################################
This message is sent to you because you are subscribed to
 the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
Send administrative queries to  <linrad-request@xxxxxxxxxxxxxxxxxxxxx>


LINRADDARNIL