[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[linrad] Re: Linux distributions
- Subject: [linrad] Re: Linux distributions
- From: comcast.net; w3sz@xxxxxxxxxxxxxxxx>
- Date: Mon, 13 Mar 2006 18:32:48 +0000
In the more recent versions of svgalib you can turn off the need for svgalib_helper by setting parameters in the config file. In earlier versions you needed to set it before compiling. i am at work and so can't give you the details, but its not hard to find the info.
rr
-------------- Original message ----------------------
From: richard <richard.bown@xxxxxxxxxxxxxxxx>
> Joe Fitzgerald wrote:
> > richard wrote:
> >
> >> I did auto complete Joe just the way it downloaded, I agree it does
> >> help sanity, when all about seem to be losing theirs :)
> >
> >
> > Well, I just tried
> >
> > [jfitzgerald@xxxxxx ~]$ wget http://www.svgalib.org/svgalib-1.4.3.tar.gz
> > --10:33:33-- http://www.svgalib.org/svgalib-1.4.3.tar.gz
> > => `svgalib-1.4.3.tar.gz'
> > Resolving www.svgalib.org... 80.74.115.3
> > Connecting to www.svgalib.org|80.74.115.3|:80... connected.
> > HTTP request sent, awaiting response... 200 OK
> > Length: 840,282 (821K) [application/x-gzip]
> >
> > 100%[=====================================================>]
> > 840,282 87.80K/s ETA 00:00
> >
> > 10:33:44 (84.00 KB/s) - `svgalib-1.4.3.tar.gz' saved [840282/840282]
> >
> > [jfitzgerald@xxxxxx ~]$ tar xfvz svgalib-1.4.3.tar.gz
> > svgalib-1.4.3/
> > svgalib-1.4.3/0-INSTALL
> > svgalib-1.4.3/0-README
> > svgalib-1.4.3/Makefile
> > svgalib-1.4.3/Makefile.cfg
> > svgalib-1.4.3/demos/
> > svgalib-1.4.3/demos/Makefile
> > ...
> >
> > and all was well. Perhaps autocomplete is tricking you? Note that if
> > you try again, autocomplete only goes as far as 'svgalib-1.4.3' - the
> > name of the directory you just untarred. Make sure you rm -rf the old
> > svgalib directory (or type out the full filename)
> >
> > -Joe KM1P
> Highly probably Joe, but 1.4.3 does not build :(
> /home/Richard/HamApps/svgalib-1.4.3/src/vga.c:3919:1: error: pasting "." and
> "HDisplay" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3920:1: error: pasting "." and
> "HSyncStart" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3921:1: error: pasting "." and
> "HSyncEnd" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3922:1: error: pasting "." and
> "HTotal" does not give
> a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3923:1: error: pasting "." and
> "VDisplay" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3924:1: error: pasting "." and
> "VSyncStart" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3925:1: error: pasting "." and
> "VSyncEnd" does not
> give a valid preprocessing token
> /home/richard/HamApps/svgalib-1.4.3/src/vga.c:3926:1: error: pasting "." and
> "VTotal" does not give
> a valid preprocessing token
> make[1]: *** [vga.o] Error 1
> make[1]: Leaving directory `/home/richard/HamApps/svgalib-1.4.3/sharedlib'
> make: *** [sharedlib/libvga.so.1.4.3] Error 2
>
> At least 9.24 does but no svga-helper
>
> Back to RPM's, at least the helpers thers !
>
> tnx
> 73 ERichard G8JVM
>
> #############################################################
> This message is sent to you because you are subscribed to
> the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
> To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
> To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
> To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
> Send administrative queries to <linrad-request@xxxxxxxxxxxxxxxxxxxxx>
>
#############################################################
This message is sent to you because you are subscribed to
the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
Send administrative queries to <linrad-request@xxxxxxxxxxxxxxxxxxxxx>
LINRADDARNIL