[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[linrad] Re: Sound problem under Debian's Sarge
I was going to tell you some directions, but I am not sure if they are
accurate cause they are based on my woody-sarge mixture machine. So, I
am going to work on my new fresh sarge install (in the spare partition)
and I will tell you.
Obviously you do not need to reinstall (this is a wrong windows habit
;-) ).
I am going to tell you some hints that can avoid some nightmares for you:
The configuration of modules is strange at the begining, but soon you
will understand that it is a very eficient way of doing things.
In Debian with 2.6 kernel, the configuration of modules is on the
/etc/modprobe.conf file . But if you look at it, you will see that
/etc/modprobe.conf "includes" the file /lib/modules/modprobe.conf. If
you go to and edit /lib/modules/modprobe.conf you will see that Debian
say :"you should not edit this file"
Well, instead, you must go to the /etc/modprobe.d/ directory
There, you will see some text files. That files include the
configuration of the modules. When the root user runs the utility
"update-modules", every file on /etc/modprobe.d/ directory is parsed,
and a new /lim/modules/modprobe.conf is created.
This is a very convenient way of doing it. When you for example install
a new Debian package, and it needs a new module, its internal scripts
create a new file in /etc/modprobe.d/ directory containing the
configuration of the needed modules. The, the package installer runs
"update-modules" command and the new module is included in the setup.
Easy, is not it?
So, the files on /etc/modprobe.d directory are the files that you need
to tweak.
This is a very general aproach. I am not sure if the utility included in
the alsa-utils package ("alsaconf") have a program to configure the
sound easier with needing to know this compications. Any way, it is
recomended to know how Debian works internally to get full control of
the system.
I am going to play a little with my fresh sarge install to confirm this.
See you again.
Ramiro.
Patrick wrote:
Hello Ramiro and all,
I have some problems with my audio system on the Debian's Sarge :
When I installed the system, the only audio board on the system was the
motherboard's built-in VT8237. Everything looked fine until I started
Linrad. The 'U' command give me the choice between 2 different boards,
both named '00' with the same VT8237 chipset.
The soundcard test mode give a sort of square signal with the
corresponding sound in the speaker...
I suspect a misconfiguration in the audio system that reports false
informations to Linrad, but I have no way to solve the problem.
I disabled the motherboard's audio device in the BIOS, and put a good
old Creative's ES1371, to see if this could not solve the problem , but
I do not know how to install it....
Well, that is my sound card.
Now Linrad reports no sound device. How could I change the audio board
without re-installing Sarge (It's fun but ...)
Very 73
Patrick
#############################################################
This message is sent to you because you are subscribed to
the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
Send administrative queries to <linrad-request@xxxxxxxxxxxxxxxxxxxxx>
#############################################################
This message is sent to you because you are subscribed to
the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
Send administrative queries to <linrad-request@xxxxxxxxxxxxxxxxxxxxx>
LINRADDARNIL